For LM238WF5-SSG7 23.8 inch FHD LCD Touch Panel
iProGadgets OEM Repair Parts for Panel LM238WF5-SSG7 — Screen Reference and Fitment Check
Quick answer: this listing is the panel on its own, code LM238WF5-SSG7 — brand-new 23.8 inch FHD 1920 x 1080 in-cell touch, IPS, anti-glare, 250 nits, 75 Hz, a 30-pin LVDS display connector plus a separate 6-pin USB touch lead. You can order it on the code alone, without telling us which computer it goes into — but the code has to match exactly. Two checks before you order: the trailing SSG7 is the part, because the other LM238WF5 suffixes we stock are 60 Hz panels built for Lenovo all-in-ones — and this is the touch panel, where the non-touch build of the machine it is usually fitted to runs at 100 Hz and has no touch lead at all. Every unit is double tested before shipping and covered by a 30-day return window on unused, uninstalled parts.
- Fit: the 23.8 inch FHD in-cell touch panel under code LM238WF5-SSG7 — 30-pin LVDS connector at the bottom left of the panel plus a 6-pin USB lead for touch, matte anti-glare surface, 75 Hz.
- Panel: an IPS panel, 1920 x 1080, matte anti-glare, 250 nits, running at 75 Hz, with an in-cell touch layer and its own 6-pin USB touch lead alongside the 30-pin LVDS display connector. In-cell means the touch sensor sits inside the LCD cell: there is no separate digitizer glass to lift, and the surface you touch is the panel's own 3H-coated cover
- Testing: every unit is double tested before shipping — display check at full resolution and a touch check across the full surface, on the bench, before it is packed
Technical Specifications
| Item | Detail |
|---|---|
| Part number | LM238WF5-SSG7, also written LM238WF5 (SS)(G7). The number is the whole identification: the SSG7 suffix is what separates this panel from the other LM238WF5 codes, which look the same in a photo and share the same connector. Supplier listings quote the screen part 18100-23800400 against it, though we have one source for that number only, so treat it as a lead rather than a fact. Read the label on the back of the panel you are removing and photograph it before ordering if there is any doubt |
| Condition | Brand-new, unassembled |
| Quality | iProGadgets OEM Quality |
| Size and resolution | 23.8 inches diagonal, 1920 x 1080 (FHD), 16:9, about 92 PPI. Active area 527.04 x 296.46 mm |
| Panel technology | a-Si TFT-LCD, IPS, normally black, transmissive, with WLED edge backlighting along the bottom edge (15S4P, 30,000 hours) and no separate backlight driver. 16.7 million colours, 89/89/89/89 viewing angles, 14 ms grey-to-grey. IPS is what makes this panel usable as a touch screen at an angle rather than straight on |
| Surface finish | Matte anti-glare, haze 25%, hard coating 3H. Every source agrees on this one, which is unusual in this family and worth saying: the anti-glare finish is what keeps a 24 inch touch panel readable in an office with windows, and it is also why finger marks wipe off rather than smear. Clean it with a dry microfibre cloth, never a solvent |
| Brightness and contrast | 250 cd/m² typical, contrast 1000:1 typical. This is the one figure every document states the same way — panel record 250 cd/m², machine page 250 nits — so there is nothing to reconcile. It is a normal office-brightness panel, not a 400 nit outdoor screen |
| Colour | 72% NTSC, which the panel record puts at 95% sRGB coverage (and 73% Adobe RGB, 75% DCI-P3). The machine page for the chassis this panel is normally fitted to states sRGB 100%. Those are the panel's own measurement and the machine's marketing figure for the same glass, and they are close rather than contradictory — but we print both rather than pick the flattering one. Expect a good, ordinary office colour range; this is not a wide-gamut editing panel |
| Refresh rate | 75 Hz. This row decides whether the listing is yours. The chassis this panel is normally fitted to was sold with more than one 23.8 inch FHD panel: the touch build runs at 75 Hz and is what this listing is, while the non-touch build runs at 100 Hz and is a different part. Some regional pages also carry an older 60 Hz row. Check what your machine reports under Settings, System, Display, Advanced display — 75 Hz with touch working means this panel |
| Touch | Yes — in-cell touch, 10 points. The touch sensor is integrated into the LCD cell, so there is no separate digitizer sheet and no air gap between glass and panel. The controller is on the panel and talks to the machine over its own 6-pin USB lead, which in practice is the single most important thing to remember at installation: the screen will show a picture with that lead unplugged, and the touch will simply not respond |
| Display interface | LVDS, 2 channels, 8-bit, 30 pins, at the bottom left as you look at the back of the panel. The metal latch lifts before the connector slides out — pull the plug body, never the cable. This is LVDS, not eDP: an eDP panel from a newer all-in-one will not connect to it even where the size matches |
| Touch interface | 6-pin USB (YEONHO 10035WR-H06D, 1.0 mm pitch), separate from the 30-pin display connector, at the bottom left as well. Seat this one first when you reassemble, because it sits closer to the frame and is harder to reach once the LVDS plug is in |
| What you receive | The panel only. No front bezel, no rear cover, no stand, no cables beyond the ones built onto the panel. Your old screen's bracket, bezel and rear housing are reused, so keep them — this is not a drop-in pre-assembled module |
| Outline and mounting | 3-side borderless, 535.12 x 313.12 x 12.76 mm overall, weight about 1.93 kg. Fixed from behind through 13 M3 mounting holes in a rear frame — there are no side brackets and no adhesive, so the panel is not bonded into the housing the way a tablet screen is. Handle it by the frame edges and never press on the glass |
| Power | 5.0 V typical, supplied over the LVDS connector. No separate inverter and no high-voltage lead — this is LED backlit |
| Operating temperature | 0 to 50 °C operating, -20 to 60 °C storage |
Compatibility
| Device | Model numbers / part codes |
|---|---|
| Panel model | LM238WF5-SSG7 / LM238WF5 (SS)(G7) |
| Screen part quoted by suppliers | 18100-23800400 — one source only; confirm on your panel label |
| NOT a standalone monitor | This is the panel inside an all-in-one; the computer sits in the same housing. It will not drive as a separate desktop display |
Before We Ship — Please Send Us These 2 Details
This listing is sold on the panel number alone, so there is no machine name to check against. That makes the label and the connectors the two things we go by. After you place the order we will contact you for both, so please have them ready:
- A photo of the label on the back of the old panel. It should read LM238WF5-SSG7. The prefix LM238WF5 is shared by a dozen 60 Hz panels built for other all-in-ones, so the trailing SSG7 is the part. If your label ends differently, tell us before we pack.
- A photo of the two connectors, or just count the pins. This panel has a 30-pin LVDS plug on the display side and a separate 6-pin USB lead for touch. If the old panel in front of you has only one lead, or the LVDS plug is 40-pin, this is not your panel — say so and we will stop the shipment rather than send a part that cannot be fitted.
We check what you send against our stock before dispatch. If something does not match we contact you first instead of shipping on a guess. Once your details are confirmed we arrange shipment within 1 to 3 business days. Thank you for helping us get it right.
Installation Notes
- Unplug the AC adapter and hold the power button for a few seconds so the board discharges. An all-in-one holds charge in its power supply long enough to damage a panel that is unplugged live.
- Remove the stand first, then the rear cover. On this family the cover unclips around its edge; work with a plastic pry tool, not a screwdriver, and keep the clips warm if the room is cold.
- With the cover off you are looking at the back of the panel in its front frame. Note where the two leads run before you release anything — the routing is tight and it is easy to pinch a cable on reassembly.
- Release the 30-pin LVDS connector at the bottom left: lift the metal latch, then pull the plug body. Never pull the cable.
- Release the 6-pin USB touch lead as well. There are two connectors on this panel, not one, and forgetting the second is the most common reason a replacement screen shows a perfect picture with dead touch.
- Undo the mounting screws and lift the old panel out by the frame. Do not press on the glass to get leverage, and do not flex the panel — the in-cell touch layer is part of the glass stack and does not survive a bend.
- Transfer anything your machine mounts on the panel itself — brackets, earth straps, the bezel — to the new panel before you seat it. This is a bare panel, so nothing comes pre-fitted.
- Clean the flex contacts with alcohol before assembly and confirm both connectors are fully seated and latched. Test the panel and the touch before you refit the rear cover.
- In Windows, confirm the resolution reads 1920 x 1080 and that touch responds across the whole surface including all four corners. Only then reassemble.
- Keep the protective film on until everything works. Handle the screen carefully, because the panel is too fragile to take pressure on its face.
Quality Control
Strictly tested by the iProGadgets QC Team — every unit is double tested before shipping and ships in good working order, including a display check at full resolution and a touch check across the full surface. After receiving the part, please check the appearance and test it first: connect the panel and the touch lead to the machine for a functional test before full installation, and only reassemble once everything works. We are not responsible for any installation mistakes — if you are not experienced with all-in-one screen replacement, have the part fitted by a professional repair shop.
Shipping
We ship worldwide. Orders are dispatched within 1 to 3 business days, and every package carries a tracking number you can follow on the order page. Delivery typically takes 7 to 10 days after dispatch.
Returns & Warranty
30-day returns on unused, uninstalled parts. The warranty is valid until installed — once a screen has been fitted, the return window no longer applies, which is why we ask you to test before installation.
FAQs
Can I order this without telling you which computer it goes in?
Yes. The panel number is the identifier, and LM238WF5-SSG7 on the label is what we match stock against — that is the whole reason this listing exists next to the machine-named one. What we will still ask for after you order is a photo of the old panel's label and a look at the two connectors, because those catch the two mistakes a part number alone cannot: a different suffix, and a machine that has no touch lead. Neither check costs you time, and both happen before dispatch rather than after.
Is this the touch panel or the non-touch one?
This is the touch panel — LM238WF5-SSG7, 75 Hz, with an in-cell touch layer and a 6-pin USB lead. The same P440VA chassis was also sold with a non-touch 23.8 inch FHD panel at 100 Hz, which is a different part with no touch layer and no touch lead. They are not interchangeable in either direction. Quick test: Settings, System, Display, Advanced display — 75 Hz and touch working means this listing, 100 Hz and no touch means you need the other panel.
The picture is perfect but the touch does nothing — what went wrong?
Almost always the 6-pin USB touch lead. This panel has two connectors: the 30-pin LVDS that carries the picture and a separate 6-pin USB lead that carries the touch data. The screen lights up and displays correctly with only the first one connected, which is exactly why the second gets missed. Open the machine again, reseat that lead at both ends, and check Device Manager under Human Interface Devices for a touch screen entry. If it is still dead with the lead properly seated, contact us — a failed touch controller is covered, and we will sort it out rather than leave you with half a screen.
Will this fit a Lenovo all-in-one that also uses LM238WF5?
We would not fit one and we will not promise it. The LM238WF5 family is shared across several all-in-one makers, and the trailing suffix is the actual part — the codes we stock for Lenovo IdeaCentre and ThinkCentre machines are 60 Hz panels, while this one is the 75 Hz touch panel. They share a 30-pin LVDS connector and look identical in photographs, so the only safe identification is the label on the panel. If your old screen says something other than LM238WF5-SSG7, send us a photo before you order and we will tell you honestly whether we can supply the right part.
Do I get the whole assembly with the bezel and the stand?
No — this is the panel only. No front bezel, no rear cover, no stand and no cables beyond the flex leads built onto the panel. Your existing bezel, brackets, earth straps and rear housing are reused, which is why the installation notes ask you to transfer them before seating the new panel. If you were expecting a pre-assembled module, tell us before ordering and we will say plainly whether we can supply one.
Questions about fit, shipping to your country, or bulk pricing? Email sales@iProGadget.com and we will confirm the exact part you need.
Frequently Asked Questions
Is this part compatible with my device?
This listing is for For LM238WF5-SSG7 23.8 inch FHD LCD Touch Panel. It is built as a direct-fit replacement for the model named in the title. Match the model number in the title against your own device before ordering. If you are not sure which version you need, email sales@iProGadget.com and we will confirm the correct part for you.
What is the quality of these replacement parts?
We supply iProGadgets OEM Quality / Premium Compatible replacement parts. Every part is manufactured to OEM specifications, so the fit, finish and function match the original component it replaces, and each unit is individually tested before it leaves our warehouse.
Is the part tested before it is shipped?
Yes. Every part we sell is inspected before dispatch and tested wherever testing applies — screen assemblies are checked on the panel, the touch response and the connector. Orders are processed and shipped within 1-3 business days after payment is confirmed.
How long does shipping take?
Orders leave our warehouse within 1-3 business days. Express Shipping (DHL, UPS or FedEx) takes 5-8 working days and is normally used for parcels over 2 kg. Registered Air Post takes 10-20 working days and is normally used for parcels under 2 kg. Every order ships with a tracking number. Customs clearance can add extra time, especially during peak season.
Will I be charged import duties or customs fees?
Customs charges depend on your own country's import rules and its de minimis threshold, not on the seller. Some destinations apply no duty at all on lower-value parcels, and where duty or VAT does apply it is collected by your local post office or courier before delivery. We ship every order with complete and accurate commercial documents, which is what keeps a parcel moving through customs instead of sitting in it. If you would like to estimate the charges before you order, email us your country and we will point you to the right authority.
What is your return policy?
We offer a 30-day return policy, which means you can request a return within 30 days of receiving your item. To be eligible, the item must be unused, uninstalled and in the packaging it arrived in. Once a part has been fitted, bonded or used it cannot be returned, so please test the part before installation. To start a return, email sales@iProGadget.com.
What should I do if the part arrives damaged or faulty?
Inspect your order as soon as it arrives. If an item is defective, damaged or not what you ordered, contact us at sales@iProGadget.com straight away with photos or a short unboxing video, and we will arrange a replacement or a refund.
Do you provide repair guides or installation tutorials?
No. We are a supplier of replacement parts only. We are not a repair shop, and we do not provide repair guides, tutorials or step-by-step installation support. Every part we sell is intended to be installed by a professional technician at a qualified repair shop, which also gives the best result: a technician can transfer the small components, handle the adhesives and test the finished repair. Please do not attempt the installation yourself if you have no previous repair experience, as these assemblies are fragile and incorrect handling can damage them permanently. We sell parts only and do not accept responsibility for installation carried out by the customer. Our warranty covers the part itself and remains valid until the part is installed. If a problem appears after the repair, please take the device back to the repair shop that fitted the part so they can inspect the installation and test the device.
Still have a question about this part? Email us at sales@iProGadget.com and we will confirm compatibility, shipping time or return details for you.
